About this deal
Wet one piece of 800 grit sandpaper - run it over the scratch in a circular motion and repeat with a dry piece of 800 grit sandpaper. Alternate between the dry and wet sandpaper, rubbing for 2 to 3 minutes. Don’t worry if your acrylic begins to look more frosty or appear to have more little scratch marks on it - this will go away during the process. Looking at the bodywork from different angles can reveal the light marks that will take the edge off any shine you add with a wax or coating. Removing them requires a scratch remover, although anything you can feel with a fingernail will probably need a machine polisher or professional attention. This article was co-authored by Jon Gholian. Jon Gholian is a Cleaning Specialist and the Founder of Cleany, a home and office cleaning concierge service based in New York City, New Jersey & Miami. Cleany specializes in providing quality cleaning and handyman services to all their customers. All Cleany employees are insured, bonded, and professionally trained. Cleany has been featured in the New York Times, Bravo & Redfin.
Hold the heat gun 2–3 in (5.1–7.6 cm) from the plexiglass and turn it on. Position the plexiglass so you can easily reach the scratch with your heat gun. Keep the heat gun's nozzle at least 2 inches (5.1 cm) from the plexiglass so you don't accidentally cause it to melt or bubble. When you're ready to start, press the power button to start the machine. [13] X Research sourceTake a dry, clean cotton or microfiber cloth. Wipe away any fragments. Warning: A dirty cloth could scratch the acrylic again! Wet a piece of 800-grit sandpaper. Run a piece of 800-grit sandpaper underneath warm water to get it damp. Shake any excess water off of the piece and wring it out so it doesn't drip. Set up your work station near a sink if possible so you can re-wet the sandpaper whenever you need to. [1] X Research source Some scratch removers don’t actually do what they say on the tin, but instead fill marks so they become less visible. No fears of that with Advanced Compound, because it is free of filler and contains no wax or silicones. Like our winner, it can be applied by machine polisher or hand, but has a 3,000-grade maximum abrasion, putting it in the same medium-cut compound range as Regenerate. It marginally topped our tests, but not by enough to overcome Regenerate’s price advantage. Rub the sandpaper over the scratch in a circular motion. The buffing motion combined with the abrasiveness of the sandpaper can help remove many scratches. Work gently, however. Being too forceful can cause new scratches. [10] X Research source
It’s worth noting that scratches can be removed more easily from acrylic than polycarbonate, so you may not have as much success if the damaged material is a polycarbonate sheet. Naturally, lighter scratches can be buffed out more easily than deeper ones. a machine polisher. Despite this, it worked well with just hand application, making good improvements to the overall shine in its section. Much like Auto Finesse’s Tripple, it could not make the same inroads on the blade marks as our top two, but it did enoughto secure a top-four finish.
Sand over the scratch in small circles for 1 minute. Apply light pressure to the scratches with your wet piece of sandpaper. Work in small, circular movements to buff the surface evenly. Sand any areas that are scratched for 1 minute, and wet the sandpaper again when it feels dry. [2] X Research source
Wipe the scratch remover off the plexiglass with a dry cloth. As soon you're done applying the scratch remover to the plexiglass, use a lint-free cleaning cloth to wipe any excess off. Work in small circles over the surface of your plexiglass. Once the scratch remover is off of your piece, you won't be able to see the scratches anymore. [11] X Research source Wet a piece of the 800 grit sandpaper and run it over the marked area in a circular motion, then repeat with a dry piece of the same grit sandpaper – you’ll need to alternative between these wet and dry sheets for around three minutes. Don’t panic if the acrylic begins to look frosty or have more scratches on it, as this is part of the process. Once you’ve done this, move on to the 1200 grit sandpaper and repeat the same process until all of the scratches have disappeared. Lastly, dry the area with a clean cotton cloth and apply the acrylic polish. The result should be a piece of acrylic that looks as good as new, with no visible marks. For deeper scratches to acrylic It’s easy to repair acrylic that has light surface scratches, which generally result from regular wear-and-tear. To begin, get a few basic items ready: product/helpAdviseTab.hbs -->