Screw Set Mounting Kitchen Tap Concealed Bathroom Fitting M6 70 mm (FW002)

Product Information

Drill Point – The drill point refers to the unthreaded section of the screw. When selecting the screw length, you should account for the length of material you are drilling through. If the threads engage before the drill point length is completely through the material it will result in the screw breaking

All that is required to insert a self tapper is a pilot hole to introduce the screw. They then form their own thread as the screw is driven into position. Once inserted, self tapping screws may be removed and re-used. SELF TAPPER SCREW In general, if the letter "B" is in a screw's designation, such as Type AB or B, it has spaced threads. If the "B" is absent, as in Type F, the screw has machine screw threads. There are two exceptions: Although considered obsolete but still available today, Type A has spaced threads. And metallic drive screws, denoted Type U, have spaced spiral threads.Look for features such as shanks that reduce wood split, twin threads for a fast and accurate drive, and tips that don’t require pre-drilling. Tapcon Countersunk Head Screws have many advantages - they can be installed close to edges, they are removable and adjustable, fire resistant and can replace small diameter expansion anchors, plugs and screws in light to medium-duty applications.

Locate Utilities - Ensure there are no electrical, plumbing, or gas lines in the vicinity of your drilling and installation area. Put on your safety goggles and, if needed, a dust mask. Insert the selected masonry bit into your power drill. Drill pilot holes into the concrete or masonry at the marked points. The pilot holes should be slightly smaller in diameter than the concrete screws you plan to use. Be sure to drill to the recommended depth, which is usually slightly deeper than the length of the screw. Step 5: CleanA self-tapping screw is a screw that can tap its own hole as it is driven into the material. More narrowly, self-tapping is used only to describe a specific type of thread-cutting screw intended to produce a thread in relatively soft material or sheet materials, excluding wood screws. Other specific types of self-tapping screw include self-drilling screws and thread rolling screws. Breaking Screws: Ensure you are using the right size and type of screw for the application and that you're not over-tightening. When using self-tapping screws, the chart below shows the suggested drill size that you should use to drill the pilot hole. I found that a good starting technique was to hold the handle close to my body, and turn with my hips, keeping my hands in the same relation to my body the whole time. I kept my eye on the end of the tap where it was held in the handle, and concentrated on that not moving sideways. After the tap has set it was fine to ease off on this and turn by hand. Self-tapping screws are screws that create their own thread as they are driven into a material, ensuring a strong, tight fit. They are best used in soft materials such as softwoods and plastic. A pilot hole that’s slightly smaller in diameter needs to be pre-drilled before fitting.

Self-tapping and drilling screws are available in steel, carbon steel, and stainless steel. Gauge sizes range from 3.5 to 6.3mm, and lengths range from 12 to 120mm. For screws that are flat on the bottom of the head including pan head, round head, truss head, etc. and hex and washer head types, the length is measured from the bottom of the head to the end point of the screw. Yes, although you will need to obtain self tapping screws specifically designed for use with concrete. After you’ve cleaned the hole, you should slowly drill the screw in place to ensure you do not strip the base material. Timber screws are specially designed for use on timber. They have an aggressive, coarse thread that grips wood securely into place. They come in various gauges, head and drive types, and sizes, meaning there is a choice of screw for any task.

3 Comments

PK-Self Tapping Screws". Archived from the original on 28 September 2017 . Retrieved 14 April 2017. Modern Plastics Encyclopedia. Vol.33. New York: Breskin & Charlton Publishing Corporation. 1955. p.41. Mark the locations where you want to install the screws. Use a measuring tape and level to mark the drill points accurately with a pencil to make precise markings on the concrete. Step 3: Select the appropriate drill bit Tapping case studies with typical examples of tapping operations in various environments are shown on source machinetoolaid.com [1] Tapping stations [ edit ]